- Router on a stick ip routing operational 9tut no further how to#
- Router on a stick ip routing operational 9tut no further install#
- Router on a stick ip routing operational 9tut no further full#
- Router on a stick ip routing operational 9tut no further password#
Once you have OpenWrt on your device, then you can use the OpenWrt sysupgrade mechanism to load sysupgrade images. You can always enter OpenWrt failsafe mode, plug in power, wait until the red light disappears, then press the button a couple of times.
Router on a stick ip routing operational 9tut no further password#
Thereafter, the router is waiting for you to log in with telnet and no password via Ethernet on IP address 192.168.1.1. Using the Administrator → Firmware menu, flash. It redirects to a wrong IP address, so type the correct one again in the URL field of the browser. Switch the language to English from the drop down menu. Find the device's IP address from your DHCP server, and log into the device using your web browser. Just connect the router with an Ethernet cable to a network, it will switch on the blue and red LEDs. I flashed OpenWrt Chaos Calmer 15.05 using the stock web interface of the device. Using your browser, open the device's home page.
Router on a stick ip routing operational 9tut no further full#
If you want to access a full shell, here's how (thanks Whiterat):Ĭonsole=ttyS1,57600n8 root=/dev/ram0 Chinese Factory Firmware Restore_defaults ->Restore the config to the default factory value. Show ->Display various talbes information, type show for help. Traceroute ->route trace, type traceroute for help. Help ->Display help information, same as '?' command.Ĭlear ->Clear various talbes, type clear for help.
Router on a stick ip routing operational 9tut no further how to#
The factory firmware is very limited most commands are disabled (but see below for how to change this). Find out the device's IP address from your DHCP server, and log into the router via telnet:īusyBox v1.12.1 ( 00:48:37 HKT) built-in shell (msh)Įnter 'help' for a list of built-in commands. The device will switch on the blue and red LEDs. With the factory firmware, just connect the router with an Ethernet cable to a network. If you don't want to mess with the plastics you can also check for the actual version via telnet by following the procedure below. The best way is to open it up (just pry it open with your fingernails or with a pry tool) and check for the A5-V11 marking on the bottom left corner of the PCB, close to the Ethernet connector. Depending on the stock firmware, an OpenWrt image may successfully be flashed from the stock firmware GUI or from the limited stock command Shell without having to open the device or mess with uboot manually.įirst, make sure you really have this device and not some other one. The resulting PCB has been copied and is populated during “grey shifts” using whatever components are at hand, and sold unbranded on Aliexpress to make a small profit.Īs of OpenWrt trunk r43793 it is supported by the Image Generator. However, this router has some drawbacks: memory (both DRAM and Flash) is limited, and actual hardware and firmware can vary a lot, even when purchased from the same vendor.īasically, a first device has been designed to fit into the given housing, based on the original Ralink RT5350F reference design, with the goal to make a 3G/4G 150M Wi-Fi router (don't be mistaken, 3G/4G is when you attach an external 3G/4G USB dongle to it!).
Router on a stick ip routing operational 9tut no further install#
With its small size (62 mm x 24 mm x 14.5 mm) and its low price tag, it is certainly one of the smallest and cheapest router onto which you can install OpenWrt. It has a tiny black or white housing about the size of a lighter, with silkscreened print “3G/4G Router 150M”. This unbranded Ralink/MediaTek RT5350F-based router is sold on Aliexpress from Chinese sellers for around 6 USD (shipped) as of July 2016.
0 kommentar(er)
